Granite Countertop Processing Note

    1、 Gross procurement requirements in the 1.95-2.15 cm plate thickness .

    2、Procurement - plate thickness in the 1.90-2.1 cm, 85 gloss over.

    3、 Large cutting processes Note:

    （1）  Stones placed in the platform should be firmly and smooth.

    （2）  To understand them clearly see the big stone cutting segmentation diagram.

    （3）  Under the knife before cutting large size correction, to review carefully and accurately.

    （4）Stone cut the first three films, the first stop of the first percutaneous stone tablets destroyed, the quality inspection Stone: whether dark crack, Glenn, stain, the color line, and other quality defects; Check whether the thickness of the first three films within the allowed tolerances (20 mm ± 5mm), and to give timely amendments

    （5）  Machine operators do before and after inspection, cleaning and maintenance, cleaning work.

    （6） Meeting: thickening plate with the best cutting edge (height), in particular on a texture of the stone.

     4、 For thick processes Note:

    （1）  Thick End determining the actual thickness of 19.5-2.0 cm. Review by vernier caliper thickness.

    （2）  Operation should carefully. Raising release sheet to the attention of safety and avoid damage to sheet metal.

    （3）  Machine operators do before and after inspection, cleaning and maintenance, cleaning work.

     5、 Large polished processes Note:

    （1）  Polish post-meeting before plastic, stone plate (especially granite) crannies filled out and avoid spent many wait until the finished human beauty fill in the plastic.

    （2）  Polish abrasive process used to set resin polish.

    （3）  Gloss over 85.

    （4）Raising caving plate to avoid inadvertently damaged sheet metal

    （5）  Leftover parts to wear that enough to gloss

     6、 Bridge shear processes Note:

    （1） To smooth upward cut.

    （2）  Saw blade to sharp. (Knife before the first head wear sharp)

    （3） To control under the knife and cutting good speed.

    （4）  Have Machining Allowance. (Cushion to 3-4 mm for 1 / 2 yen at the seams stereotypes stereotypes to within 0.3 mm).

    （5）there is texture of the stone to a cutting edge even thickening out with such textural Large thickening of the texture edge to be fair, finished only beautiful natural. (Set a number, and if there are patterns even when the direction of direction).

    （6）To avoid missing Prism, missing Kok, not completely cut off, cutting distortions, such as the wrong size phenomenon

    （7）  Machine operators do before and after inspection, cleaning and maintenance, cleaning work.

     7、Gluing stereotypes processes:

    （1）  Palette carefully, as far as possible will be redeployed to the basic and plastic stone color consistency.

     （3） Before gluing matched the best selection of sheet metal contacts for bonding.

    （2）  Thickening of the plate and a plate to keep secret. A dense, using metal clip, fixed, and let it laminated.

    （4） After the completion of glue joints is not more than 0.3 mm.

    （5）In bonding, it is necessary to pay attention to the glue No, it is necessary to stem excess glue shaved his, avoid refined beauty, flowers in many human on scraping gum.

     8、 1 / 2 Circle stereotypes processes Note:

    （1） Because of the Machining Allowance (3-4 mm), to 1 / 2 yen Machining Allowance than the original when no more than 3-4 mm deep set, glue joints after not more than 0.3 mm.

    9、 Hand processing that processes Note:

    （1）50 degrees angle radians.

    （2）  That should be as far as possible, smoothing over natural corner. The surface should be formed.

    （3） Careful handling to avoid damage to granite countertop.

     10、 Small polished surface processes Note:

    （1） Sheet metal or wooden size metal frame that came to the put away and avoid injury Taiwan panel edge in order to maintain angular integrity.

    （2）  Gloss over 85.

    （3）  Small surface grinding have to be carefully and comprehensively. Straight to straightening curves to smooth over-natural, corner of the mill to place.

    （4）  Phase angle or excessive wear to the Department should not feel without scalloped feeling edge grinding to a little hands will not scratch.

      11、 Fill plastic cosmetic procedures Note:

    （1） Stone should be placed in strict accordance with the names, color Division, placing neat and orderly manner. Open, the need to fill plastic edge in the same direction, forming a straight line. This ease of effective, rapid and accurate fill plastic beauty.

    （2） Palette carefully, as far as possible will be redeployed to the basic and plastic stone color consistency.

    （3） To master the glue dry time. Avoid

too dry scraping can not glue or glue not disturbed, even plastic scratch.

     15、This "granite countertop processes processing diligence" by the quality control staff circulated to a Road processes.

    （5） No haphazard display, all kinds of stone mixed together.

    （6）  Fill plastic staff by a color stone varieties or division positioning.

    （7）Fill plastic End, we should clean up the venue. Tools placed neatly.

    12、Note removal process (the procedures required attention, in particular the forklift Handling)

    （1）102 mm retaining plate on the prototypes, no-placed.

    （2） Smooth to-face display.

    （3）  Use of soft-bonding (such as foam) back pad. Avoid scratches the surface. .

    （4）  Forklift removal process should be careful, take the necessary protective measures to avoid forklift encountered obstructions or uneven pace of sheet metal fell, damage.

     13、 Packaging processes Note:

    （1） By leveraging the wooden box packaging exports.

    （2） Located, moving to be careful and meticulous

    （3） Face-to-face emissions. Middle use styrofoam / foam / plastic separated to avoid surface damage.

    （4）A firm producing wooden box; Wooden box to needle firmly.

     14、Finished processing all daily operations to maintain work sites clean, tidy and health.

    （4）  Fill plastic should be careful to avoid inadvertently unification, the sheet metal stamping on the break. No sitting on the sheet metal fill plastic operations.